測量原理Measureprinciple本儀器測量原理為直角坐標測量法，即通過X軸、Z1軸傳感器，測繪出被測零件的表面輪廓的坐標點，通過電器組件，將傳感器所測量的坐標點數據傳輸到上位PC機，軟件對所采集的原始坐標數據進行數學運算處理，標注所需的工程測量項目
本儀器測量原理為直角坐標測量法，即通過X軸、Z1軸傳感器，測繪出被測零件的表面輪廓的坐標點，通過電器組件，將傳感器所測量的坐標點數據傳輸到上位PC機，軟件對所采集的原始坐標數據進行數學運算處理，標注所需的工程測量項目。
The measuring principle of this instrument is the rectangular coordinate measuring method,through X-axis, Z-axis sensor, mapping the surface contour coordinates point of the part under test,data transmission the coordinates point to the upper PC by electrical components.To do the mathematical treatment on the original collected coordinate data by software, marked with the required engineering survey projects.
測量功能 Measuring function
1、輪廓測量功能
尺寸：包含水平距離、垂直距離、線性距離、半徑、直徑
夾角：包含水平角、垂直角、夾角
位置公差：包含平行度、垂直度
形狀公差：包含直線度、凸度、圓弧輪廓度
輔助生成：包含輔助點、輔助線、輔助圓
Size: contains the horizontal distance, vertical distance, linear distance, radius and diameter
Angle: horizontal Angle and vertical Angle, Angle
Position tolerance: contains the parallelism and perpendicularity
Shape tolerance: contains the straightness, crown, circular arc profile
Auxiliary generation: contains the auxiliary point, auxiliary line, auxiliary circle
2、粗糙度測量功能
測量參數Measure items： Ra、Rt、Rp、Rz(jis)、Rz（DIN）、Rz、Rvk、Rv、R3z、Rs、Rsm、Rc、Rsk、Rk、Rmax、Rpk、Mr1、Mr2、Rq、Rku、R△q
| 項目 Item | 參數 Parameter | |
| X軸 | 測量范圍 Measuring range | 120mm |
| 檢測方法 Detection method | 新型數字式傳感器/分辨率：0.2μm New digital sensor Resolution：0.2μm | |
| 測量速度 Measurement Speed | 0.1，0.2,0.5,1mm/s 自定義 | |
| 驅動方式及速度 Drive mode and Speed | 電動 4檔，可自定義速度 Electric ，4 gear，can customize speed | |
| 直線度 Straightness | 1.2μm/100mm | |
| 線性精度 Linear accuracy | ±（1.5+0.025L）μm | |
| Z1軸/輪廓部分 | 量程 Sensor range | 24mm |
| 線性精度 Linear accuracy | ±（1.2+|0.04H|）μm | |
| 檢測方法 Detection method | 新型數字式傳感器/分辨率：0.01μm New digital sensor Resolution：0.01μm | |
| 水平精度 | ±（1+0.025L）μm | |
| 垂直精度 | ±（0.8+|0.03H|)μm | |
| Z1軸/粗糙度部分 | 傳感器量程范圍 Sensor range | 800μm/80μm |
| 分辨率 Resolution | 12nm（800μm量程時） 1.2nm（80μm量程時） | |
| 截止波長 Cut-off wavelength | 0.025、0.08、0.25、0.8、2.5、8mm | |
| 測量重復性 Repeatability | ±3% | |
| 線性精度 Linear accuracy | ±5% | |
| 評定長度 Evaluation length | λc×3、4、5、6、7 | |
| Z軸 | 立柱行程 Column travel | 400mm |
| 驅動方式及速度 Drive mode and Speed | 電動 4檔，可自定義速度 Electric ，4 gear，can customize speed | |
技術特點 Technical characteristics
① X、Z1均采用新型數字式傳感器，精度更高
② 大量程設計，杠桿比僅為1:2.2，限度保持了傳感器的原有精度
③ 高剛性高精度直線運動導軌、高精度數字式線性傳感器
④ 采用高速并行數據采集單元，硬件觸發、硬件高速采樣，無延時；足夠密集及穩定的數據源為后期數據處理、計算提供力的保障
⑤ 更換傳感器部分即可實現粗糙度測量。
① X, Z1 adopt imported new digital sensor, higer precision ;
② Design in a wide range, leverage ratio is 1:2. 2, the maximum keep the original precision of the sensor;
③ High rigidity, high precision linear motion guide rail, high precision digital linear sensor;
④ Using high speed parallel data acquisition unit, high-speed sampling hardware trigger, hardware, without delay. Dense and stable source provide the most powerful guarantee for later data processing, calculation.
⑤ Roughness measurement can be achieved by changing the sensor part.
輪廓測量軟件系統 Software System
強大的系統功能
軟件兼容winXP、win7、win8系統 Software support XP、win7、win8 system.
軟件支持中英文 Software support Chinese and English language.
快捷自由的頁面布局
軟件增設快捷鍵，方便使用 Software add shortcuts, easy to use
支持將菜單及控制區收起操作，以擴大繪圖區的有效區域面積 Support pack up the menu and control operation, to enlarge the drawing effective area
豐富的數據處理系統
圓弧、線自動識別 Automatic identification of circular arc, the line
擬合可選擇點選或框選 Fitting choice click or marquee
軟件標注與CAD同理 Software similarly marked with CAD
支持連續標注、基準標注、支持任意插入點 Support continuous annotation and datum mark, support any insertion point
支持圖形自由旋轉及坐標自由旋轉 Support the freedom of graphic rotation and coordinate rotation
支持坐標點標注 Support the coordinate points label
捕捉開關打開時，自動生成及捕捉交點、圓心 、線段中點、端點、圓弧交點、中點、切點等特征點
While capture switch is opened, automatically generated and capture the intersection point, circle, line midpoint, endpoint, circular intersection, midpoint, point of tangency feature points, etc
完善的數據保存模式
原始數據自動保存，便于多次標注 Original data automatically saved, facilitate multiple labels
可將測量的圖形結果轉化成DXF格式 Measurement graphic results can be transferred into DXF forma
鏡像功能，可保存標注后文件 The mirror function, can save after standard file.
便捷的控制方式
可對Z1、X軸當前位置進行監控 Can monitor the current position of the Z1, X axis
測量長度可任意設定 Measuring length can be set freely.
具有測針自動接觸、自動抬起、自動回退功能 Needle automatic contact, automatic lift, automatic back.
可以對操作進行無限次的撤銷及恢復操作 The operation can be unlimited undo and restore
SP2000特色的功能
非比例放大：即使在非比例放大的情況下，也能進行正常的角度、圓弧、水平、垂直、線性等標注。
自動標注：在進行批量測量時，測量保存為模板，再次測量導入模板即可完成自動標注，大大提高測量效率。
數據合成：對于類似直槽工件無法一次測量完成，通過擺放角度進行兩次測量，然后通過軟件進行數據合成。
間斷測量：可對工件進行分段編程（采樣間隔、采樣速度），提高客戶測量效率。
粗糙度測量軟件 Roughness Software System
特色數據再處理功能：當實際測量部分與需要被測量部分有差時，可框選出需要進行數據處理部分的粗糙度曲線，將該部分曲線截取出來重新處理分析。Data reprocessing: After the measurement is completed, you can select the data processing part of the measurement curve to reprocess the analysis.
測量圖形不僅可等比放大，且可單軸非比例放大。Measurement graphics can not only be magnified, but also uniaxial non-proportional amplification.
測量報告分為當前報告及統計報告，統計報告可用于分析同個工件重復測量數據及同批量工件的測量數據，便于用戶直觀看出數據的變化。The measurement report is divided into the current report and the statistical report, and the statistical report can be used to analyze the repeated measurement data of the same workpiece and the measurement data of the same batch of workpieces, so that users can see the change of the data intuitively.
環境要求 Environment Specifications
電 源：AC 220V±5% 50Hz 單獨地線
功率需求：約500W
環境要求：現場溫度：15～25℃、理想溫度：20±2℃
相對濕度：＜85%
室內周圍應無影響測量的灰塵、振動、噪音、氣流、腐蝕性氣體和較強磁場
Power supply： AC 220 v + 5% for 50 hz Seperate groud wire
Power requirements: about 500 w.
Environmental requirements: the temperature: 15 ~ 25 ℃, ideal temperature: 20 + 2 ℃
relative humidity: < 85%
Around the indoor should have no affect the measurement of dust, vibration, noise, air, corrosive gas and strong magnetic field.
設備配置 Equipment configuration
售后服務 After-sale service
Extra Warranty Period: we will take telephone and regular visit to users as after-sale advisory service.
Our company is responsible for the technical advisory services of metrology for user free of charge.
We will provide life warranty services of machine for users with cost price.
If we get telephone service request about equipment failure from users, we will response to the request in 24 hours,
We have spare parts in stock, will provide life warranty services of spare parts for users with cost price We will provide users with lifelong after-sales value-added technical service，such as technical upgrades，retrofit，etc.by preferential prices.
If there is my company’s office in the region of the users, it will fully responsible for the after-sale technical services.
|
|
|
|
|
|
*您想獲取產品的資料：
個人信息：
